An energy band is a range of allowed electron energies in a crystal, formed when the discrete levels of many atoms overlap. The bandgap (Eg) is the forbidden range between the top of the valence band and the bottom of the conduction band: 1.12 eV for silicon and 3.39 eV for GaN at 300 K.
Key takeaways
- Bandgap sets intrinsic carrier density, optical absorption edge and critical field.
- Direct-gap materials (GaAs, InP, GaN) emit light efficiently. Indirect-gap materials (Si, Ge, SiC) do not.
- The cut-off wavelength in nanometres is about 1240 divided by Eg in eV.
- The Fermi level sits near midgap in pure material and moves toward a band edge with doping.
Bandgap of common semiconductors at 300 K
| Material | Eg at 300 K (eV) | Gap type | Cut-off wavelength (nm) | Typical use |
|---|---|---|---|---|
| Si | 1.12 | Indirect | About 1,110 | Logic, power, solar cells |
| Ge | 0.66 | Indirect | About 1,880 | Infrared detectors, SiGe transistors |
| GaAs | 1.42 | Direct | About 870 | RF front ends, infrared LEDs and lasers |
| InP | 1.34 | Direct | About 925 | Telecom lasers and detectors, high-frequency HBTs |
| 4H-SiC | 3.23 to 3.26 | Indirect | About 380 | Power devices at 1,200 V and above |
| GaN (wurtzite) | 3.39 | Direct | About 365 | Blue and UV LEDs, RF and power HEMTs |
What are energy bands?
An isolated atom has sharp energy levels. Bring N atoms together in a crystal and each level splits into N closely spaced levels, because neighbouring electron wavefunctions overlap. With around 1022 atoms per cm3, those levels form effectively continuous bands. Stronger overlap, from shorter bond length or lighter atoms, gives wider bands and usually a different gap.
Kittel treats this as electrons moving in a periodic potential: allowed bands appear, separated by gaps where no travelling wave solution exists. Our articles on band types and on what sets band width go further.
What is the difference between valence and conduction bands?
The valence band holds the bonding electrons. When it is completely full, its electrons cannot carry net current. The conduction band is the next band up. An electron promoted into it moves freely and conducts, and the empty state it leaves in the valence band behaves as a positive carrier, the hole.
In a metal the highest occupied band is only partly filled, so conduction needs no excitation. In a semiconductor, conduction depends on how many electrons cross the gap. See valence and conduction bands explained and conductivity.
How to read a band diagram
A band diagram plots electron energy (vertical) against position in the device (horizontal). Electron energy increases upward, so electrons roll down and holes float up. From top to bottom, the labelled lines are:
- Evac, the vacuum level: the energy of an electron at rest just outside the material.
- χ, the electron affinity: the gap from Evac down to EC (about 4.05 eV for Si).
- EC, the conduction band edge: the lowest energy a free electron can have.
- EF, the Fermi level: drawn as a dashed line; flat everywhere in equilibrium.
- Ei, the intrinsic level: close to midgap.
- EV, the valence band edge: the highest energy of the bonding states. Eg = EC − EV.
Sloping bands mean an electric field. A step in EC or EV means a heterojunction. Our guide to interpreting band diagrams works through examples.
What is a direct bandgap?
In a direct-gap semiconductor, the conduction band minimum and valence band maximum occur at the same crystal momentum. An electron can drop across the gap and emit a photon in one step. In an indirect-gap material the two extremes sit at different momenta, so a lattice vibration (phonon) must take part. That makes emission slow and inefficient.
This is why LEDs and lasers use GaAs, InP and GaN, while silicon is used for detectors and solar cells but not light sources. Alloying can move a material across the line: AlxGa1-xAs turns indirect at about x = 0.4 to 0.45. See band-to-band transitions, Band Gap Energy and bandgap engineering with alloys.
Where does the Fermi level sit?
The Fermi level EF is the energy at which a state has a 50% chance of being occupied. In undoped material it sits near midgap. Donor doping pushes it toward EC; acceptor doping pulls it toward EV. For n-type material, EC − EF = kT ln(NC/ND), where NC is the effective density of states (about 2.8 × 1019 cm-3 in Si) and kT is 0.0259 eV at 300 K. A donor density of 1016 cm-3 puts EF about 0.21 eV below EC.
Bandgap itself shrinks as temperature rises: silicon’s is about 1.17 eV at 0 K and 1.12 eV at 300 K. Read more in Fermi Energy Level, the Fermi level article and the doping hub.
All energy band guides
Band structure basics
- Unleashing the Power of Semiconductors: A Deep Dive into Different Types of Energy Bands
- Unmasking the Secrets of Semiconductors: Unveiling the Role of Energy Bands
- Empowering Technology: The Indispensable Role of Energy Bands in Semiconductor Devices
- Unraveling the Mysteries of Semiconductors: Factors Influencing the Width of Energy Bands
- The Dynamic Duo of Semiconductors: Understanding the Valence and Conduction Bands in Energy Bands
- Unlocking the Code of Semiconductors: Interpreting Energy Band Diagrams
Bandgap and transitions
- The Heart of Semiconductors: Deciphering the Role of Bandgap Energy in Energy Bands
- Powering Progress: Band-to-Band Transitions, the Lifeblood of Semiconductor Energy Bands
- Band Gap Energy
Fermi level and doping
- Fermi Level: The Hidden Puppeteer Behind Energy Bands in Semiconductors
- Fermi Energy Level
- Sculpting Semiconductors: How Doping Transforms Energy Bands and Revolutionizes Technology
Semiconductor fundamentals
FAQs
- What are the main advantages of semiconductors over metals?
- Why are semiconductors special?
- Are semiconductors easily damaged by high temperature?
- What are the disadvantages of semiconductor?
- What are the advantages and disadvantages of semiconductor devices?
- What is the resistivity of a semiconductor?
- What is the principle of semiconductor?
- What are the 3 properties of semiconductors?
Related physics hubs
FAQ
Is silicon a direct or indirect bandgap semiconductor?
Indirect. Its conduction band minimum lies away from the centre of the Brillouin zone, so radiative recombination needs a phonon. That is why silicon makes good photodetectors and solar cells but poor LEDs.
How does the bandgap set the colour of an LED?
The emitted photon energy is close to the bandgap. Wavelength in nanometres is about 1240 divided by Eg in eV, so GaAs at 1.42 eV emits near 870 nm (infrared) and InGaN wells near 2.7 eV emit blue light.
Does the bandgap change with temperature?
Yes, it narrows as temperature rises because the lattice expands and vibrates more. Silicon falls from about 1.17 eV at 0 K to 1.12 eV at 300 K; GaAs from about 1.52 eV to 1.42 eV.
Sources
- S. M. Sze and K. K. Ng, Physics of Semiconductor Devices, 3rd ed., Wiley.
- C. Kittel, Introduction to Solid State Physics, 8th ed., Wiley.
- Ioffe Institute, New Semiconductor Materials (NSM) archive, http://www.ioffe.ru/SVA/NSM/Semicond/

