Wednesday, November 18, 2026
CS Fusion The compound semiconductor reference
Comparisons

Semiconductor Comparisons: Side-by-Side Property Tables

Si, SiC, GaN, GaAs, InP and Ga2O3 compared at 300 K: bandgap, mobility, thermal conductivity and critical field, plus every head-to-head guide.

Semiconductor comparisons are side-by-side property tables for the materials engineers actually choose between: silicon, SiC, GaN, GaAs, InP and Ga2O3. Every value is quoted at 300 K, with units and a source. Start here for bandgap, mobility, breakdown field and thermal conductivity, then follow the links to each head-to-head guide.

Key numbers at 300 K

Six materials cover most of the commercial decisions in power, RF and optoelectronics. The table gives the four properties that drive those decisions. Mobility values are upper limits for pure, lightly doped crystal; real device layers sit lower because doping and temperature both scatter carriers.

MaterialBandgap (eV)Gap typeElectron mobility (cm²/V·s)Thermal conductivity (W/m·K)Critical field (MV/cm)
Si1.12Indirect≤1,400130–150~0.3
4H-SiC3.26Indirect≤900~370~2–3
GaN (wurtzite)3.39Direct≤1,000 bulk; ~2,000 in a 2DEG channel130–230~3.3
GaAs1.42Direct≤8,500~55~0.4
InP1.34Direct≤5,400~68~0.5
β-Ga2O3~4.8Indirect (nearly direct)~150–200~10–27 (direction-dependent)~8 (estimated)
Source: Ioffe Institute NSM archive for Si, 4H-SiC, GaN, GaAs and InP. β-Ga2O3 is not in the Ioffe archive; its values come from review literature (Pearton et al., 2018), and its critical field is a theoretical estimate. GaN thermal conductivity depends on dislocation density. 2DEG = two-dimensional electron gas at an AlGaN/GaN interface.

The full 20-material version, with hole mobility, permittivity and lattice constants, is in our semiconductor properties table.

How do semiconductor materials compare on bandgap and mobility?

Bandgap and electron mobility pull in opposite directions. The bandgap is the energy needed to free an electron so it can carry current. A wide gap gives a high critical field and low leakage when hot. Mobility measures how fast electrons drift per volt of applied field, and the highest values belong to narrow-gap III-V compounds with light electrons.

That splits the table in two. GaAs and InP have gaps near 1.3–1.4 eV and electron mobility four to six times silicon’s, so they dominate RF front ends, lasers and fast photodetectors. SiC, GaN and Ga2O3 trade mobility for gaps of 3.3–4.8 eV and critical fields 7 to 27 times silicon’s, which is what power electronics needs. Silicon sits in the middle and wins on cost and process maturity. Our bandgap comparison and carrier mobility comparison go deeper on each axis, and the GaAs hub explains why direct gaps matter for light emission.

Which is better, GaN or SiC?

Neither wins everywhere. The split is mostly by voltage and frequency. GaN transistors are lateral HEMTs (high-electron-mobility transistors) that switch very fast with low charge, and most commercial parts are rated from about 15 V to 650 V. SiC MOSFETs are vertical devices that scale to 1,200 V, 1,700 V and above, and SiC conducts heat about twice as well as GaN-on-Si.

Pick GaN for compact chargers, data-centre supplies and RF power amplifiers. Pick SiC for traction inverters, solar and industrial drives at 800 V bus voltages and up. The GaN vs SiC guide sets out the voltage map, GaN vs silicon covers the low-voltage side, and SiC MOSFET vs Si IGBT covers the high-voltage side. For material detail, see the GaN hub and the SiC hub.

Which material has the highest thermal conductivity?

Diamond leads every practical semiconductor at about 2,000–2,200 W/m·K. Among the six materials in the table, 4H-SiC is the clear leader at about 370 W/m·K, more than twice silicon’s 130–150 W/m·K. GaN sits between 130 and 230 W/m·K depending on crystal quality. GaAs and InP fall to 55–68 W/m·K, and Ga2O3 is lowest at roughly 10–27 W/m·K.

This matters because heat sets the power density a die can survive. It is the main reason RF GaN is often grown on SiC substrates, and the biggest engineering obstacle for Ga2O3 power devices. Our thermal conductivity comparison covers temperature dependence and substrate effects.

Which figures of merit are used to compare materials?

A figure of merit combines several properties into one number that predicts device performance. Two are used most often:

  • Baliga figure of merit (BFOM) = ε·μ·Ec3, where ε is permittivity, μ is mobility and Ec is critical field. It predicts the lowest on-resistance a power device can reach at a given blocking voltage. The cube on Ec is why wide-bandgap materials score hundreds of times higher than silicon.
  • Johnson figure of merit (JFOM) = Ec·vsat/2π, where vsat is saturated electron velocity. It ranks materials for high-power, high-frequency transistors, which is where GaN stands out.

Single properties still matter on their own. Permittivity sets capacitance, and resistivity tells you how a wafer behaves as a substrate or insulator. See the breakdown field comparison, the dielectric constant comparison and the resistivity comparison.

How do I choose a semiconductor material?

Start from the constraint that binds first, then check cost and supply. A quick guide:

  • Pick silicon when cost, wafer size and process maturity dominate. It covers logic, memory and most power below a few hundred volts.
  • Pick SiC when you need blocking voltages from about 650 V up to several kV, high junction temperature or the best heat removal short of diamond.
  • Pick GaN when switching frequency and power density matter between roughly 15 V and 650 V, or for RF power at microwave frequencies.
  • Pick GaAs or InP when you need high electron mobility or a direct gap: RF front ends, lasers and photodetectors. InP is the base for 1.3 µm and 1.55 µm telecom lasers.
  • Consider Ga2O3 when you work on ultra-high-voltage devices and can live with poor heat removal and no practical p-type doping. It remains largely at the research and early-product stage.

For background on the categories themselves, start with the quick answers on elemental vs compound semiconductors and organic vs inorganic semiconductors.

Start here

All comparison guides

Head-to-head device and material comparisons

Property-by-property comparisons

Quick answers

Browse by material

New comparison guides

Frequently asked questions

Why are the values quoted at 300 K?

300 K (about 27 °C) is the standard reference temperature in data compilations such as the Ioffe archive. Most properties shift with temperature: bandgap narrows, mobility falls and thermal conductivity drops as a device heats up, so always compare at the same temperature.

GaAs has six times silicon’s electron mobility. Why is it rarely used for power devices?

Its critical field (about 0.4 MV/cm) is barely above silicon’s, and its thermal conductivity (about 55 W/m·K) is less than half. For power, critical field and heat removal matter more than mobility, which is why SiC and GaN took that role.

Is Ga2O3 better than GaN and SiC?

On critical field, yes: about 8 MV/cm is the estimate, against about 3.3 for GaN and 2–3 for 4H-SiC. On heat removal and p-type doping, it is much worse. It is a promising ultra-high-voltage material, not yet a general replacement.

Sources

  • Ioffe Institute, New Semiconductor Materials (NSM) archive: Si, SiC, GaN, GaAs and InP property pages. http://www.ioffe.ru/SVA/NSM/Semicond/
  • B. J. Baliga, Fundamentals of Power Semiconductor Devices, Springer (Baliga figure of merit, drift-region design).
  • S. M. Sze and K. K. Ng, Physics of Semiconductor Devices, 3rd ed., Wiley (band structure, mobility, breakdown).
  • S. J. Pearton et al., “A review of Ga2O3 materials, processing, and devices,” Applied Physics Reviews 5, 011301 (2018).
Malcare WordPress Security